When deciding to install a 2020+ Clarion, Kicker or JL Audio digital marine radio and corresponding wired remote control; the CMRR-C5 is a must!
Many boat owners wanting to install the newest Clarion, Kicker or JL Audio digital marine remote control (e.g. CMM-30, MM105 etc.) to the dive platform, transom etc. are faced with having to run yet another extension cable; but if boat already has a 6-pin DIN extension cable; the CMRR-C5 cable makes it possible to install a 2020+ radio/remote in minutes and for less than $100. One conversion cable connects the new radio the extension cable in cabin, etc. and connects the newest remote to the other end of the extension cable (upper deck, transom, dive platform etc.) it's that easy!
Who can benefit from this conversion cable kit?
- Any boat with a 1st generation (1998-08) Clarion marine radio and wired remote; will have this 6-pin DIN extension cable (e.g. M101RXC-RET, MW-RXC-RET etc.) already fitted.
Conversely:
- 2nd generation (2009-Up) Clarion marine radios and wired remotes; use 8-pin DIN extension cable (e.g. MWRXCRET etc.) or a 6-pin DIN extension with the CCUMRA1 and/or CUMRA2 adapter.
- 3rd generation (2020-Up) Clarion, Kicker and JL audio digital marine source units (radios) and wired remotes requires a 5-pin non-NMEA 2000® extension cable (e.g. CMC-RC-25, MMC-6 etc.) or use the 6-pin DIN extension cable (already fitted), with our CMRR-C5 cable kit.
» Connect select 2020+ marine digital receivers (e.g. CMM-20 etc.) to matching wired marine remote control (e.g. CMR-10, MMR-20 etc.) using 1st generation 6-pin extension cable.
» Works with Clarion: CMM-30, CMM-20, CMM-30BB, CMR-30, CMR-20, CMR-10
» Works with Kicker: KMC5, KRC55
» Works with JL audio: MM105, MM55, MM105-HR, MMR-20-BE
» Matching 5-pin non-NMEA 2000® (male/female) connector/plug (Fits the 5-pin remote plug on source unit)
» Matching 6-pin DIN plug/connector fits 6-pin "extension cable" (M101RC) or 6-pin splitter cable (M101RYC) already fitted
» Avoids having to re-wire boat with a CMC-RC-25, MMC-6 25 or 6-foot cable.
» 2 part male/female conversion cables (6 inches long)
» Not applicable to JL Audio MMR-40
Installation
1. Locate 6-pin "boat" extension cable behind OEM radio or cavity. Note if there is no 6-pin extension cable, this cable kit will not apply.
2. Locate the 5-pin remote cable on the Clarion, Kicker or JL Audio digital receiver
3. Connect CMRR-C5 5-Pin male plug to the 5-pin radio remote cable connector.
4. Connect CMRR-C5 6-pin connector to the extension cable 6-pin plug (leading to remote control).
5. Go to remove location and locate the extension cable 6-pin connector behind wired remote cavity
6. Connect CMRR-C5 6-pin female to extension cable 6-pin plug
7. Connect CMRR-C5 5-pin connector to the 5-pin remote control (e.g. CMR-10) plug.
Click INSTALL DIAGRAM to better illustrate the connection.
Alert: The CMRR-C5 harness works only in boats with the 6-pin pre-wired extension cable already fitted.
1. Use to install recent Clarion, Kicker & JL marine remote/receiver in any boat with a 6-pin male to female extension cable. Must have 6-pin DIN extension cable already fitted.
2. Not suitable to mix and match between brands. Both the remote and source units must be of the same brand.
3. Made by DiscountCarStereo.com for use on recent Clarion, JL Audio and Kicker digital marine products only.